Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Have you been in search of info around How to Install a Bathtub Yourself?
Mounting a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably difficult task. If the old tub is conveniently available, the project can relocate immediately; if you need to open up a wall surface to eliminate the old tub as well as place the new tub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the job as well as fit attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This short article will certainly help you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and do not require to alter the plan of your previous water pipelines.
Your devices and also product checklist need to make up the following:
Getting ready for the Installation
To start with, the supporting framework supplied with the bath needs to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. When the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wood boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub up until the level reads degree.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub needs to wait up until the bath tub has been used at least once as this will resolve it into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin making sure that the washers remain in area in between the faucet as well as the sink. Protect the tap in position with the maker provided backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type needs to be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a stiff seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, resulting in complications with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the activity experienced when the tub is in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Leave a short review below. We'd be delighted to find out your opinions about this content. In hopes to see you back again in the future. Be sure to set aside a second to distribute this page if you liked it. Thank you for your time spent reading it.
Visit Link Report this page